Why Replacing Upvc Window Handles Is Your Next Big Obsession

Replacing uPVC Window Handles

It is simple to swap the handles on upvc windows. It is important to ensure that the new handle is fitted into the spindle cutout in the window mechanism.

If you follow the steps below the handle of any cockspur will fit in most windows. The most important factor is the step in the height of the handle.

What to Look for

As time passes, uPVC handles on many windows in the UK may begin to show signs wear and tear. The handle on the window may become shaky or difficult to operate when this occurs. This is a easy task that can be accomplished by anyone who is comfortable with basic hand tools.

The first step is to ensure that the handle is securely fixed to the frame of the window and in its open position. The next step is to find the screws or pins which hold the handle in place. These are typically located on the inside face of the handle and are removed using a screwdriver or pliers.

When the handle is loose, gently pull it away from its hinges. It is then time to find a replacement handle with the same design and size. This can be done at a DIY store or online. The procedure should take just five minutes and a screwdriver is all you need.

When replacing the handle on a uPVC handle it is essential to consider the step height. This is the distance from the bottom of the handle to the point at which it sits on the frame of the window. This is a standard measurement and you should check the height of the step prior to ordering a replacement handle.

There are several sizes depending on the kind of handle. Inline handles for uPVC windows usually have lug centres of 31mm as well as cockspur handle types that have 43mm centres. Tilt-and turn handles are typically found on uPVC windows. They feature a unique design that lets the window be tilted to allow for ventilation and then turned to fully open the window.

The most common cause of breakage in uPVC handles is that they crack inside instead of breaking off from the base section. This can make them hard to open and therefore it is essential to ensure that any replacement handle you purchase has the same spindle length as your existing one.

Remove the old Handle

A poorly fitted or damaged window handles could cause your double glazed windows to close or open incorrectly, and can result in them getting stuck. There are a variety of reasons for this including general wear and tear, or corrosion of the metal handle. In these cases it is essential to locate replacement upvc window handles immediately in order to avoid further damage and loss of function.

One of the first steps to do when replacing window handles made of upvc is to remove the old handle from the window. Start by removing the screw with the handle when it is in a closed position. Once you have removed the screw, you can take off the handle. It is a good idea to employ an electric screwdriver to accomplish this as it will make the task much easier and quicker.

It is also important to be aware that screws may be hidden in plastic caps. It is recommended to remove the covers with a Stanley knife. After the handle has been removed, you must look at the square cut out at the handle's base to ensure that the new window lock handles are compatible with it. It is important to measure the length of the spindle on the handle that was used and compare it to the dimensions of the window mechanism spindle cutout.

The different types of window handles made of upvc are: Espag handles, which feature a central screw that can turn left or right; Cranked handles which have two screws and are typically found on tilt and turn windows made of upvc as well as Spade handles, with an arm with a flat surface and can be put on either side of the window. When you have a suitable replacement, it's simple to screw the handle into place and ensuring that the spindle is inserted into the lock mechanism. After that, it should be tightened to the window frame and your replacement upvc window handles should be secure.

Measure the Spindle

If you're replacing a Upvc window handle that has fallen off, it is likely because the spindle holding it in place has become loose or damaged. In some cases this can be fixed by using a screw or pin to secure it. In some cases, it may be necessary to replace the handle. There are a variety of upvc handles. There are three types of handles: inline espagnolette, tilt-and-turn, and cockspur. Each type of handle is mounted and replaced in a different manner.

It is essential to measure the current handle before purchasing a replacement. This will help ensure that the new handle is of the correct size and will fit correctly into the window. All handles are calibrated in accordance with industry standards, making it easy to identify the correct size.

To determine the size of the handle move the window to the open position. You should be able to see the size of the screw or pin that secures the handle. Make use of a ruler or tape measure to determine how long the spindle is. Once you have the length of your spindle, it is possible to purchase a replacement of the exact same length.

The step height of a upvc window handle is also a factor to consider when purchasing replacements.  window handles repairmywindowsanddoors.co.uk  is the distance from the base of the handle to where it is placed on the frame. Typically, this is approximately 21mm for uPVC windows or 9mm for aluminium. Dropping objects into the gap will let you see how far the handle extends before it meets an obstruction.

Cockspur handles can have different backsets, based on the type of window you put them in. Inline the espag handle heights range from 43mm from the centre to the centre (two fixing points). Cockspur handles however, have different backset heights depending on the style of the window they're in. This is because they have a spur which extends from the handle and locks onto a cockspur wedge hitting plate.

Install the new handle

After you've chosen the new handle, align it carefully with the holes for screws on the door. Then, secure it with the screws supplied. If you're also replacing the latch lever the lever can be mounted similarly to the main door handle. Then, you can reattach the door trim to hide the screws for mounting and finish the job.

Tips: To remove a metal head from a wedge made of wood, place the handle on the floor so that its wide end is on the floor. Then use to tap the thin end. Be careful not to scratch the handle or spindle.